• Adam Huda Nugraha Gunadarma University
  • Sandy Suryady Gunadarma University



Pneumatic Systems, The process of making pc wire heads


Pc wire or Prestressed concrete wire is iron thread with a round cross section and has indentations on its surface. Pc wire is widely used in the construction of buildings or buildings, railway sleepers and piles. This paper discusses the process of making pc wire heads and pneumatic systems that function as driving hammer dies in making pc wire. The aim of the research is to know the work process of making pc wire head (screw iron), calculating the pneumatic system for making pc wire head (screw iron). The data needed in the preparation of this report was obtained by collecting data, namely field studies which are direct data collection. data obtained through direct observation in the field accompanied by a field supervisor then Literature Study where literature study is data collection through literature books, journals, making pc wire heads by cutting pc wire with a diameter of 7.1 mm along 152 mm using a cutting grinder and then clamping it in a vise so that the screw iron does not shift when getting pressure from the die, the die will press the pc wire so that it is formed with a circular diameter of 13 mm and 7 mm thick. From the calculation of the density of dry air, the result is = 87.08 Pa, the result of the hydrostatic calculation is 609.78 Pa, and from the calculation of the Double Acting Cylinder, the result is 254.34 N.


Manual Book, Mesin Heading, PT. Adhimix Precast Indonesia. Jakarta 2002.

Dines Ginting, Thomas Krist. Dasar-Dasar Pneumatik : Prinsip Dasar, Komponen, Perhitungan, Pelaksanaan, Jakarta 1993.

Sugihartono. U, Dasar-Dasar Kontrol Pnuematik,, Tarsito, Bandung 1985.

Croser.P dan Ehel.F, Pnuematik, Festo Didatic, Esslingen 1992.

Cahyono H., Dedy, Perbaikan Mutu Pada Proses dan Produksi Spun Pile Dengan Menggunakan Metode Taguchi,Surabaya 1997.

Parr, Andrew. 2003. Edisi Kedua, Hidrolika dan Pneumatik. Penerbit Erlangga.

Stewart, Harry L. 1978.Hydraulic and Pneumatic Power for Production. Industrial Press Krist,.

Thomas. 1993. Dasar-Dasar Pneumatik. Pnerbit Erlangga: Jakarta .

Ogata, Katsuhito. 1996. Edisi Kedua, Teknik Kontrol Automatik. Erlangga : Jakarta.

Croser, P. 1994. Pneumatik, Tingkat Dasar P. III. Festo Didactic.

Sari, S. P., & Suryady, S. (2018). Koefisien Perpindahan Panas Konveksi dan Simulasi Distribusi Temperatur Aliran Fluida pada Penukar Kalor Pipa Ganda dengan Pipa Spiral.

Muchlis, A., Suryady, S., & Ramadhan, A. R. A. (2022). PEMPROSESAN FIXTRUT MENGGUNAKAN MILD STEEL PADA PIPA SCHEDULE 40 UK. 1 INCH. Jurnal Technopreneur (JTech), 10(2), 25-30.

Suryady, S., & Nugroho, E. A. (2022). Simulasi Faktor Keamanan Dan Pembebanan Statik Rangka Pada Turbin Angin Savonius. Jurnal Ilmiah Multidisiplin, 1(02), 42-48.

Muchlis, A., Suryady, S., & Nugroho, A. (2021). Frame Head Production Process In Category 3 Frame Chassis At Pt. Prime Dual Core. International Journal of Science, Technology & Management, 2(5), 1780-1786.




How to Cite

Adam Huda Nugraha, & Sandy Suryady. (2023). INFORMATION SYSTEM FOR MAKING PC WIRE HEADS WITH PNEUMATIC SYSTEMS IN HEADING MACHINE. International Journal Science and Technology, 2(2), 61–65.