ANALYSIS OF MASS FLOW RATE IN COLD WATER INTO FLOW WITH HOT WATER OUTPUT TEMPERATURE IN SHELL AND TUBE HEAT EXCHANGER
DOI:
https://doi.org/10.56127/ijst.v1i2.135Keywords:
Analysis, Heat exchanger , shell and tubeAbstract
A heat exchanger is a device used to exchange heat and can usually function as a heater or a cooler. There are many types of heat exchangers available today. But the most widely used in industry is the shell and tube type heat exchanger. The shell and tube type heat exchanger has the advantages of being affordable, easy to maintain and has excellent heat transfer performance with a small volume. This paper aims to analyze the effect of mass flow rate on cold water inflow and hot water outlet temperature using water fluid in shell and tube heat exchanger. The design analysis that I did using the Solidworks 2019 software. This study only made a comparison by changing the mass flow velocity at the inflow of cold water with samples of 5 Kg/s, 10 Kg/s, 15 Kg/s, 20 Kg/s, 25 Kg/ s and 30 Kg/s and only sampled the hot water outlet temperature. The material used is stainless steel 321 on the shell and copper on the tube. The test results show that every increase of a multiple of 5 Kg/s there is a decrease in the average fluid temperature of 1.62 ℃ and the lowest temperature that can be achieved in this test is 52.33 ℃
References
Suhirman, S. (2009). Aplikasi Teknologi Pemurnian Untuk Meningkatkan Mutu Minyak Nilam. Perkembangan Teknologi TRO, Vol. 21, No. (1), Hal. 15-21.
Setya, Novita H, Aprilia Budiarti, dan Mahfud. 2012. Proses Pengambilan Minyak Atsiri Dari Daun Nilam Dengan Pemanfaatan Gelombang Mikro (Microwave). Surabaya: Jurusan Teknik Kimia, Fakultas Teknologi Industri, Institut Teknologi Sepuluh Nopember (ITS).
Ambarita, Himsar. 2012. Perpindahan Panas Konduksi dan Penyelesaian Analitik dan Numerik. Medan: Departemen Teknik Mesin FT USU.
Koestoer, Raldi Artono. 2002. Perpindahan Kalor Untuk Mahasiswa Teknik. Ed. Jakarta: Salemba Teknika.
Incroperara, F. P. and D. P. Dewitt. 1982. Fundamental of Heat and Mass Transfer, Third Edition. Singapore: John Wiley & Sons.
Ambarita, Himsar. 2011. Perpindahan Panas Konveksi dan Pengantar Alat Penukar Kalor. Medan: Departemen Teknik Mesin FT USU.
Buchori, luqman. 2011. Perpindahan Panas. Semarang : UNPID.
Holman, J. P., 2010, Heat Transfer, Tenth Edition-10th Edition, McGrawHill. USA.3. McCabe, W., Smith, J.C., and Harriot, P., 1993, “Unit Operation of Chemical Engineering”, McGraw Hill Book, Co., United States of America.
Linsley, Ray K. 1972. Teknik Sumber Daya Air Jilid 1. Jakarta : Erlangga.
Cengel, Yunus A, 2003. Heat Transfer a Practical Approach. New York:Mc Graw Hill.
Ikhsan. 2012. Project of Jilin 60,000t/year Ethanolamine.
ZA, Tendra, et al., 2011. Pengantar Operasi stage Seimbang. Yogyakarta: Gadjah Mada University Press.
Hana, Indah Pratiwi dan Linna Noviarti,. 2012. Evaluasi Kinerja Heat Exchanger 11E-25 Pada Preheating Section Dalam Crude Distilling Unit IDI PT Pertamina (Persero) Refinery Unit IV Cilacap. Teknik Kmia. Politeknik Negri : Bandung.
Setiawan, I. 2011. Mempertahankan Kinerja Alat Penukar Kalor dengan Memodifikasi Sistem Kerja Feeded Pump. Teknik Mesin. Universitas Indonesia: Jakarta
